Blower,
designation*
A
B
C
D
D1
E
F
G
H
J
K
N
P
S
T
V
2332-38/2-_75C
18
16
5⁄8
22
½
88
2
5⁄8
29
7⁄8
43 31
½
18
¼
36
½
25
½
72
5⁄8
1
¼
18 9
¼
3
¼
2332-38/2-_100C
18
16
5⁄8
22
½
89
7⁄8
4
½
29
7⁄8
43 31
½
18
¼
36
½
25
½
72
5⁄8
1
¼
18 9
¼
3
¼
2332-38/2-_125C
18
16
5⁄8
22
½
89
7⁄8
4
½
29
7⁄8
43 31
½
18
¼
36
½
25
½
72
5⁄8
1
¼
18 9
¼
3
¼
2332-41/2-_75C
12 23
1⁄8
23
½
97
2
5⁄8
34
¼
50
15⁄16
38 25
1⁄8
37
½
33
¾
76
1
¾
16 9
1⁄8
3
¾
2332-41/2-_100C
16
23
1⁄8
23
½
98
7⁄8
4
½
34
¼
44 38 25
1⁄8
37
½
33
¾
76
1
¾
16 9
1⁄8
3
¾
2332-41/2-_125C
16
23
1⁄8
23
½
98
7⁄8
4
½
34
¼
44 38 25
1⁄8
37
½
33
¾
76
1
¾
16 9
1⁄8
3
¾
2338-41/2-_75C
12
23
1⁄8
23
½
97
2
5⁄8
34
¼
44 38 25
1⁄8
37
½
33
¾
76
1
¾
16 9
1⁄8
3
¾
2338-41/2-_100C
12
23
1⁄8
23
½
98
7⁄8
4
½
34
¼
44 38 25
1⁄8
37
½
33
¾
76
1
¾
16 9
1⁄8
3
¾
2344-38/2-_75C
18
16
5⁄8
22
½
88
2
5⁄8
29
7⁄8
43 31
½
18
¼
36
½
25
½
72
5⁄8
1
¼
18 9
¼
3
¼
2344-38/2-_100C
18
16
5⁄8
22
½
89
7⁄8
4
½
29
7⁄8
43 31
½
18
¼
36
½
25
½
72
5⁄8
1
¼
18 9
¼
3
¼
2344-38/2-_125C
18
16
5⁄8
22
½
86
¾
1
3⁄8
29
7⁄8
43 31
½
18
¼
36
½
25
½
72
5⁄8
1
¼
18 9
¼
3
¼
To fully ascertain overall clearances, check the dimension
combinations shown at right for the particular discharge
position selected.
discharge
overall dimension
discharge
overall dimension
position
height
width
position
height
width
1
G+K
F+K
3
E+G F+K
2
F+G
E+K
4
G+K E+K
*
Explanation of designation: 2304-11/1-_.3C means 2300 series, 4 osi pressure, inner housing no. 11,
1⁄3
hp motor, coupled drive.
"SW"
means sleeve or weld. A fl exible rubberized sleeve (Bul-
letin 2947) can be slipped over an SW connection and clamped to
prevent leaks. A fl exible connection dœ s not transmit vibrations
or stresses as do welded or threaded connections. Blowers are
not designed for imposed loads from hard pipe connections and
should not be "hard" piped except under unusual circumstances.
Discharge Connections:
A threaded (female) fl ange (Fig. 1) is available
with blowers of 6" and smaller discharge pipe size. An SW connection
(Fig. 2) is available for 8" and larger, or may be specifi ed for smaller
sizes (Fig. 3).
Inlet Connections:
An SW inlet (unthreaded, Fig. 2) for sleeve or welding
connection is availabe. A threaded female inlet (Fig. 3) may be speci-
fi ed for 3" through 6" inlets. For an open inlet, an inlet guard should be
specifi ed (Fig. 1). Blowers should not be operated without inlet protec-
tion.
Fig. 1.
Fig. 2.
Sheet 2300-11
Page 4
All dimensions are in inches. Dimensions shown apply only to blowers with T-frame motors.
Consult North American for dimensions of blowers with other motors.
Fig. 3.
Inlet or outlet adapters are not included as standard supply and must be specifi ed at an additional cost.
Cop
yr
igh
t © 2020 - F
iv
es - All r
igh
ts r
eser
ved | Shee
t 2300-11 03/10
WARNING:
Situations dangerous to personnel and property may exist with the operation and maintenance of any combustion equipment. The presence of fuels, oxidants, hot and cold combustion products, hot
surfaces, electrical power in control and ignition circuits, etc., are inherent with any combustion application. Components in combustion systems may exceed 160°F (71°C) surface temperatures and present hot
surface contact hazard. Fives North American Combustion, Inc. suggests the use of combustion systems that are in compliance with all Safety Codes, Standards, Regulations and Directives; and care in operation.
Fives North American Combustion, Inc.
4455 East 71st Street - Cleveland, OH 44105 - USA
www.fi vesgroup.com
CONTACT
fna.sales@fi vesgroup.com
T +1 800 626 3477 - F +1 216 373 4237
